permanent mold
英 [ˈpɜːmənənt məʊld]
美 [ˈpɜːrmənənt moʊld]
网络 金属模; 永久型铸造
双语例句
- The performance, role, potential value and application ways of heat pipe in light alloy in permanent mold casting were expounded.
初步评估了热管在轻合金永久型铸造中的行为、作用、利用潜力和应用的基本形式。 - The rheological characteristics of a new permanent mold coating for magnesium alloys was studied in this paper, and the rheological curve was fitted by the rheological model.
研究了一种镁合金金属型涂料的流变特性，并用流变模型对流变曲线进行了拟合。 - Process Optimization and Numerical Simulation for Shock Absorber Sleeve in Permanent Mold Casting
减震器筒体金属型铸造过程模拟及工艺优化 - The cylinder and bands may be examined by a spectator before the drum is formed. Process Optimization and Numerical Simulation for Shock Absorber Sleeve in Permanent Mold Casting
在组装鼓之前圆筒和金属圈都可以被观众检查.减震器筒体金属型铸造过程模拟及工艺优化 - Numerical Simulation of Filling and Solidification Process for Damper Cylinder of Motorcycle in Permanent Mold Casting
摩托车减震筒金属型铸造充型凝固过程数值模拟 - Study on Rheological Characteristics of Permanent Mold Coating for Magnesium Alloys
镁合金金属型铸造涂料流变性能的研究 - Crystal grains of castings by aluminum mold are less than that of castings by iron permanent mold, and mechanical properties are obviously improved.
经微弧氧化涂层处理的铝质金属型比铁质金属型铸出的铸件组织更细，力学性能明显改善。 - Analysis for Defects of Water Faucet Handle by Permanent Mold Casting
金属型铸造水嘴手柄缺陷分析 - Study on Exhausting of Permanent Mold Cavity in Low-pressure Casting
金属型低压铸造型腔排气的研究 - Study on the Effect of Iron for the Aluminum Alloy Piston in Permanent Mold
金属型铸造活塞铝合金中铁的作用研究 - Designing Parameters for Permanent Mold Used in Al-Alloy Castings
铝合金铸造用金属型设计参数研究 - Technology Optimization and Quality Control of the Aluminium Inlet Manifolds in Permanent Mold Gravity Casting Process
金属型铸造汽车铝合金进气歧管的工艺优化与质量控制 - The Centrifugal Casting Process of Copper Alloy Making Use of Moulding Sand Covering on the Permanent Mold
铜合金金属型覆砂离心铸造工艺 - In this paper the difference between water simulation and permanent mold is analysed, and the formula of the size ratio of water simulation model is derived.
分析了水力模拟与金属型铸造的差异，依据相似原理，导出了水力模拟应遵循的相似条件及模型设计比例尺公式。 - Designing of Insulating Riser for Permanent Mold Casting by Modulus
模数法设计金属型铸造铝活塞保温冒口 - Permanent Mold Casting Technology to Improve Quality of Al-alloy Damping Cylinder
提高铝合金减震筒质量的金属型铸造工艺 - Permanent mold casting technology for large copper bush
大铜瓦的金属型铸造工艺 - Based on the permanent mold casting process of Al-piston, with top insulating riser feeding process, semi-permanent insulating sleeves matching permanent mold casting process of Al-piston have been designed.
根据金属型铸造铝活塞的工艺特点，采用顶部保温冒口补缩工艺，设计了能与铝活塞金属型铸造工艺相匹配的半永久型保温冒口套。 - Permanent Mold Casting of Al-Si Alloy Body Case
Al-Si合金壳体的金属型铸造 - The movable pool and permanent mold of electroslag pouring ( ESP) have been designed.
设计了电渣转铸的活动熔池和固定结晶器。 - Study on the Gating System of Permanent Mold Casting for Al Alloy
铝合金金属型铸造浇注系统设计研究 - Technological Aspects in Design of Permanent Mold for Aluminum Piston in Casting Machine
铝活塞金属型设计的工艺问题 - Study on Semi-permanent Insulating Riser for Permanent Mold Casting of Al-piston
金属型铸造铝活塞半永久型保温冒口工艺研究 - A Study on Structure and Properties of Multicomponent Low Alloy Mill Balls Produced with Single-ball Permanent Mold Process
单球金属型工艺生产多元低合金磨球组织与性能研究 - Numerical Simulation of the Function of Heat Exchange Coefficient in Permanent Mold of Piston
热交换系数在活塞金属型铸造工艺中的作用的数值模拟研究 - Study of low temperature graphitization of permanent mold malleable cast iron
金属型铸造可锻铸铁的低温石墨化退火研究 - The study was taken an oil sump as an example to analyze crack defect of permanent mold aluminum casting with thin thickness, deep cavity and large plane, and two causes, thermal stress and shrinkage stress during casting solidification.
以油底壳为例，分析了壁薄、深型腔、大平面铝合金金属型重力铸件，产生裂纹缺陷的原因，确定是合金凝固时期的热应力和收缩应力所致。 - The Analysis of the Thermal Fatigue of Grey Cast Iron Permanent Mold for Centrifugal Cast Iron Pipe
离心铸铁管用灰铸铁金属型热疲劳性能的研究 - The results show that mechanical properties of semi-solid specimens are higher than the liquid casting in permanent mold, except for the tensile strength of the semi-solid specimen corresponding to the integrated slurry making process.
研究了液态和半固态金属型浇注试样的组织和力学性能，结果表明，半固态金属型试样的力学性能高于液态金属型（除复合制浆方法所得半固态试样的抗拉强度低于液态金属型外）。